User Tools

Site Tools



This shows you the differences between two versions of the page.

Link to this comparison view

guisetup50 [2019/05/06 15:09]
root created
guisetup50 [2020/06/25 22:05] (current)
Line 1: Line 1:
 =====Interface settings===== =====Interface settings=====
-“User interface ​settings” module ​can be found under the path: Menu → Service. This module allows to fine tune some parameters of user web interface ​of ICS CUBE.+The "​Interface ​settings" ​module ​is located in the "​Maintenance"​ menu. This module allows ​you to configure ​some parameters of the web-interface.
-“Language” field allow to select the language of the web interface.+==== General settings====
-“User view” allows to toggle the way users are shown in the interface between a tree and a list.+{{:​guisetup1.png?|}}
-“Session timeout” ​allows to set timeout ​for a session. Timeout is the period upon elapse of which the session with web interface ​will be closed after last user’s action. Please note, that if the web interface shows a page with dynamic contents ​(with constant updates), this session will not be closed even if the user is inactive after set session timeout period.+The "​Language"​ field allows ​you to select the language ​for displaying ​the web interface (Russian or English).
-“Enable IP auth” flag allows ​all users with IP address configured in ICS CUBE to pass authentication and authorization without entering login and password.+The "Users view" field allows ​you to set the user display type in the "​Users"​ module. Data can be displayed in the form of a tree or a list.
-“Web interface port” ​field allows to set the port at which to connect  ​the web interface. ​It is port 81 by default+The "​Session timeout" ​field allows ​you to set the timeout period in minutes. The session timeout determines the time of inactivity of the ICS CUBE user in the web interface, ​at the end of which the user will be disconnected (logged out) from the web interface. ​Please note that if the web interface ​is open on a page with dynamic content, the session timeout will not occur.
-“Certificate for web interface” field allows ​to select a certificate to use HTTPS protocol to connnect to ICS CUBE. By default ICS CUBE creates certificate for itself and signs it «Autogenerated GUI…». Since ICS CUBE signs it itself, your web browser will complain that the certificate is unreliable. In order to enter web interface of ICS CUBE you need to add this certificate to your web browser.+The "​Enable IP auth" flag allows ​all users registered on the ICS CUBE with the specified IP-address ​to go through the authorization and authentication process without entering a username and password.
-“Webmail port” field allows to set the port, where web interface of ICS CUBE mail works. By default it is 81 and you have to append “/rc/” after the port number in URL to access web mail of ICS CUBE. Alternatively just follow the “Web-mail” link in Mail module of ICS CUBE (Menu → Mail → Web-mail). If you change the default webmail port, the web-mail will be accessible via the following URL: <IP address of ICS CUBE>:<​new webmail port number>. Also if you change the default webmail port make sure you have set webmail certificate in the “Certificate for webmail” field. If you set webmail port value to 80, than you will need to explicitly set proxy in your browser of use transparent proxy of ICS CUBE, in the latter case enter ICS CUBE own IP address in “Transparent proxy exceptions” field in  “Menu → Network → Proxy → Settings”.+==== Ports and certificates====
-“Certificate for webmail” field serves the same purpose as “Certificate for web interface”. Self-signed certificate has the name “Autogenerated MailServer…”. This field may be left empty if the value of “Web interface port” and “Webmail port” are the same.+{{:​guisetup2.png?|}}
-“Hide ​link to web mail in authorization window” checkbox ​allows ​not to show link to web mail in ICS CUBE login window.+The "Web interface port" field allows you to specify the port on which the ICS CUBE web-interface works. By default, it is port 81. 
 +The "​Certificate for web interface"​ field - since the ICS CUBE web-interface only works over https, you need to have a certificate to access the web interface. By default, ICS CUBE creates the "​Autogenerated GUI…"​ self-signed certificate. Since the certificate is self-signed,​ all Internet browsers will consider it as not reliable. In order to access the ICS CUBE web-interface,​ you need to add this certificate to the Internet browser. 
 +The "​Webmail port" field allows you to specify the port on which the web interface of the ICS CUBE mail works (Roundcube). By default, this is port 81, but to access the web interface of the ICS CUBE mail, you need to enter "/​rc/"​ in the address bar after specifying the port. Or, when logging in to the ICS CUBE web-interface,​ click on the "​Webmail" ​link. If you change the default port number, access ​to the mail web-interface will be in the format <ICS CUBE IP-address>:<​newly set port>. Please note that when changing the default port, the certificate shall be specified in the "​Certificate for webmail"​ field, since the web interface of the ICS CUBE mail is available over https. If port 80 was specified, then when accessing web mail, you need to either specify an explicit proxy in the browser or use a transparent proxy in the ICS CUBE, but in the "​Transparent proxy exceptions"​ field, you must specify the IP-address of the ICS CUBE. 
 +The "​Certificate for webmail"​ field is similar to the "​Certificate for web interface"​ field. The self-signed certificate has the following name: "​Autogenerated MailServer..."​. This field may be left blank if the values for the "Web interface port" and "​Webmail port" fields are the same. 
 +==== Links in the authorization window. ==== 
 +The "Hide link to webmail"​ flag allows ​you to hide the "​Webmail"​ link in the ICS CUBE authorization window. 
 +The "​Hide ​link to Xauth" flag allows you to hide the authorization program link that helps in downloading the xauth program ​in the ICS CUBE authorization ​window
 +In order for the changes to be applied, click the "​Save"​ button.
-“Hide link to authorization program in authorization window” checkbox allows not to show link for xauth program download in ICS CUBE login window. 
-When finished editing apply changes by clicking “Save” button. 
guisetup50.txt · Last modified: 2020/06/25 22:05 by zog